TKR0280.030
Stay variant 030 – with externally opening and detachable crossbars
Properties
- Low-vibration plastic frame with particularly long service life thanks to molded chain links.
- Swivable and detachable on one side in any position.
- Outside: Swivable and detachable
- Inside: detachable
Stay arrangement on each chain link (VS: fully-stayed)
Pictographs
Inner height
Outer height
Inner width
Outer width
Inner width (Bi) in x mm increments
Pitch
Bending radius
Long travel length
Travel length unsupported
Travel length gliding
High additional load
High travel acceleration
High travel velocity
Stay arrangement on every 2nd chain link
Stay arrangement on every chain link
Cannot be opened
Opens outward
Opens inward
Opens inward/outward
Covered cable carrier
Sliding dividers
Fixable dividers
Fixable dividers in x mm grid
Height separation possible
Height separation in 1 mm increments
Hole stay available
Guide channel required
Strain relief
Clean room suitable
Quiet running/low noise
Sold by the meter
Low weight
ESD material
Ex-protection-material
Heat-resistant
Cold-resistant
Resistant to hot chips
Flame-resistant V0 (UL94)
Flame-resistant V2 (UL94)
Dimensions
The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.
Calculating the cable carrier length
hi
[mm]
|
hG
[mm]
|
Bi
[mm]
|
Bk
[mm]
|
qk
[kg/m]
| |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 52 | 66 | 50 | 62 | 75 | 87 | 100 | 125 | 150 | 200 | Bi + 30 | 2.00 – 3.20 |
KR
[mm]
| |||
|---|---|---|---|
| 75 | 100 | 150 | 200 |
Order example
TKR0280
100
030
150
840
VS
Inner distribution
The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (Version A).
Fixable dividers are available for applications with lateral accelerations and for applications lying on the side.
The arresting cams click into place in the locking grids in the crossbars (version B).
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3 | 8 | 5.6 | – | – |
| B | A | 8 | 5.6 | 4 | – |
| A | Bi [mm]
aT min [mm]
| 50 5 | 62 7 | 75 5.5 | 87 3.5 | 100 6 | 125 6.5 | 150 7 | 200 4 |
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3 | 8 | 5.6 | – | 2 |
| B | A | 8 | 5.6 | 4 | 2 |
| A | Bi [mm]
aT min [mm]
| 50 5 | 62 7 | 75 5.5 | 87 3.5 | 100 6 | 125 6.5 | 150 7 | 200 4 |
| Vers. |
aT min
[mm]
|
ax min
[mm]
|
ac min
[mm]
|
ax grid
[mm]
|
nT min |
|---|---|---|---|---|---|
| A | 3 | 26 | 20 | – | 2 |
| B | A | 28 | 22 | 4 | 2 |
| A | Bi [mm]
aT min [mm]
| 50 5 | 62 7 | 75 5.5 | 87 3.5 | 100 6 | 125 6.5 | 150 7 | 200 4 |
The dividers are fixed by the partitions, the complete divider system is movable in the cross section.
Aluminum section subdivisions are only available with ax > 26 mm.
Order example
TS0
A
3
VD0
VD1
Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.
End connectors
UMB end connectors UMB – plastic
The universal mounting brackets (UMB) are made from plastic and can be mounted from the top, from the bottom or face on.
Recommended tightening torque:
0,6 Nm for screws M4
Bi [mm] |
BEF [mm] | nz |
|---|---|---|
50 | 80 | 2 x 3 |
62 | 92 | - |
75 | 105 | 2 x 5 |
87 | 117 | - |
100 | 130 | 2 x 7 |
125 | 155 | 2 x 9 |
150 | 180 | 2 x 11 |
200 | 230 | - |
F – fixed point
M – driver
U – universal mounting bracket
Order example
UMB
F
U
UMB
M
U
UMB
UMB
F
M
U
U
We recommend the use of strain reliefs at the driver and fixed point.
